bays, , , , , , , " />

Pro Audio Equipment

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Comments Off
Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays

Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays. This listing is for an extremely rare and sought-after Calrec HN5642 XR Rackmount Mixing Console. The items have been used, therefore show a few stickers and use marks. But it is good cosmetic condition – We have not tested the units in any way, however all items have been removed from a fully working and functioning UK based radio station, in the past 3 weeks. The details for the units are as follows. DSP & Digital I/O Rack. The 7U DSP/Digital I/O rack houses the systems DSP, input, output and control cards. Incorporated into the rack is a built-in low noise fan tray, situated above the processing area. The fan tray incorporates a baffle such that warm air is drawn out of the rack and out through the rear of the fan tray. 1 DSP card (UD5763). 1 control processor card (UN5764). 1 GPIO card (WY5647). 1 ADC (analog input) card (AD5766). 1 DAC (analog output) card (DA5767). Up to 2 AES input/output cards (JI5765). Mounting – The unit should always be mounted in a horizontal position, located into an equipment bay and secured into the front of the bay by the four fixing holes in each of the two front angles. Synchronisation – The system can be pre-set with up to five external sync sources, plus internal, such that if the 1st source fails, it will automatically switch to the 2nd, and so on. It is strongly recommended that all items of digital equipment connected digitally to the console, are synchronised to the same sync signal. If the consoles internal sync is to be the master, other digital equipment should be synchronised to the digital outputs of the console. External AES Sources – Please note that the facility for locking to external AES sources is restricted to the first six inputs of each AES card in the console. One of the external sources can be Video, (PAL or NTSC). TTL Wordclock is another possible external source. TTL Wordclock – Synchronisation A TTL Word Clock synchronisation input is provided on the rear of the Digital I/O Rack, on a 75 BNC connector. Frequency Variation – When using a digital input or wordclock as a source, the system will tolerate a variation of up to +/- 100 Hz in the frequency of the source. The console may also be synchronised from its internal crystal oscillator (48 kHz). ZN5650 Multi-Rail Power Supply. A 1U multi-rail power supply unit is used to power the DSP/Digital I/O Rack. This unit houses two multi-rail power supply units – one powering the rack, plus a second unit acting as a hot spare providing redundancy, in case the first unit fails. Each PSU within the unit has an IEC inlet. Power Output Connections – An 8 way connector for Analog power connects to the rear of the DSP/Digital I/O rack, providing power to its analog components. A 5 way connector for 24V power connects to the rear of the DSP/Digital I/O rack, providing power to its digital components. Mounting – This unit should be secured into the front of the bay by the two standard fixing holes in each of the two 1RU front angles. The unit should always be mounted in a horizontal position. PSU Fail Indication. Should any of the fans slow down or stop, or any voltage rail fall outside specified limits, a PSU Fail signal will be sent to the console and front end via relays, to warn the operator of a problem. A 9 way D-type connector receives the fan status of the DSP/Digital I/O rack. A 36 way SCSI style connector provides the link back to the DSP/Digital I/O rack for the fan fail signal to be sent to the consoles front end via AWACS. Rack Reset – Pressing the RACK RESET button resets the DSP/Digital I/O rack only, the control surface is unaffected. Please Note: Resetting the racks will result in a brief audio interruption. Fan Cooling – The multi-rail power supply unit is fan cooled using low noise fans. Acoustic Noise Level – The acoustic noise of the unit is 42dBA. This measurement was taken at 1 metre from the dominant noise source. The unit is supplied with 2 EDAC/ELCO Panels, with the connecting wires still attached. You have around 30cm of free cable before it terminates into a MDR plug. Mic ADC / AD5766 – 800-105-74 Revision 5. DAC / DA5767 – 803-063-52 Revision 5. GPIO / WY5647 – 809-054-22. AES / JI5765 – 809-040-37 Revision 3. PROC / UN5764 – 820-124-7 Revision 1. DSP / UD5763 – Bluefin2 820-123-44 Revision 4. Everything you see in the photos is included. Not including the Power Cable (Unless otherwise stated). Please see our other items for other Vintage and Rare broadcast equipment, including more Technics, Rogers and much more! Any questions please ask, and feel free to make any offers. The item “Calrec HN5642 X2 DSP & Digital I/O 7U Rack + ZN5650 PSU + Multiple Cards + Bays” is in sale since Wednesday, July 26, 2017. This item is in the category “Musical Instruments\Pro Audio Equipment\Mixers”. The seller is “used-studio-equipment” and is located in Peterborough. This item can be shipped to United Kingdom.
  • Brand: Calrec
  • Analogue/Digital: Digital
  • Suited For: Studio/Recording
  • MPN: X2
  • Powered/Non-Powered: Powered

Posted by admin on July 27th, 2017 :: Filed under calrec
Tags :: , , , , , , ,